Benchmark ADC16 Datenblatt Seite 79
- Seite / 153
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
ST72334J/N, ST72314J/N, ST72124J
79/153
SERIAL PERIPHERAL INTERFACE (Cont’d)
14.4.4.5 Master Mode Fault
Master mode fault occurs when the master device
has its SS
pin pulled low, then the MODF bit is set.
Master mode fault affects the SPI peripheral in the
following ways:
– The MODF bit is set and an SPI interrupt is
generated if the SPIE bit is set.
– The SPE bit is reset. This blocks all output
from the device and disables the SPI periph-
eral.
– The MSTR bit is reset, thus forcing the device
into slave mode.
Clearing the MODF bit is done through a software
sequence:
1. A read or write access to the SR register while
the MODF bit is set.
2. A write to the CR register.
Notes: To avoid any multiple slave conflicts in the
case of a system comprising several MCUs, the
SS
pin must be pulled high during the clearing se-
quence of the MODF bit. The SPE and MSTR bits
may be restored to their original state during or af-
ter this clearing sequence.
Hardware does not allow the user to set the SPE
and MSTR bits while the MODF bit is set except in
the MODF bit clearing sequence.
In a slave device the MODF bit can not be set, but
in a multi master configuration the device can be in
slave mode with this MODF bit set.
The MODF bit indicates that there might have
been a multi-master conflict for system control and
allows a proper exit from system operation to a re-
set or default system state using an interrupt rou-
tine.
14.4.4.6 Overrun Condition
An overrun condition occurs when the master de-
vice has sent several data bytes and the slave de-
vice has not cleared the SPIF bit issuing from the
previous data byte transmitted.
In this case, the receiver buffer contains the byte
sent after the SPIF bit was last cleared. A read to
the DR register returns this byte. All other bytes
are lost.
This condition is not detected by the SPI peripher-
al.
- ST72334J/N 1
- ST72314J/N, ST72124J 1
- Table of Contents 2
- 2 INTRODUCTION 6
- 3 PIN DESCRIPTION 7
- (N versions) 8
- (J versions) 9
- 4 REGISTER & MEMORY MAP 13
- 5 FLASH PROGRAM MEMORY 17
- 6 DATA EEPROM 18
- Interrupt enable 21
- Latch Access Transfer 21
- 8 CENTRAL PROCESSING UNIT 23
- Half carry 24
- Interrupt mask 24
- Negative 24
- Carry/borrow 24
- 00000001 25
- MAIN CLOCK 26
- CONTROLLER 26
- ■ an external source 30
- ■ an external RC oscillator 30
- LVD reset flag 32
- Clock security syst 32
- interrupt enable 32
- Watchdog reset flag 32
- 10 INTERRUPTS 33
- INTERRUPTS (Cont’d) 34
- Table 5. Interrupt mapping 34
- 11 POWER SAVING MODES 35
- 12 I/O PORTS 39
- Hardware Configuration 41
- OPEN-DRAIN OUTPUT 41
- PUSH-PULL OUTPUT 41
- Data register 8 bits 44
- Option register 8 bits 44
- I/O PORTS (Cont’d) 45
- 13 MISCELLANEOUS REGISTERS 46
- Main clock out selection 47
- CPU clock prescaler 47
- Slow mode select 47
- Must always be cleared 48
- Beep control 48
- SS mode selection 48
- SS internal mode 48
- 14 ON-CHIP PERIPHERALS 49
- Activation bit 50
- 7-bit timer (MSB to LSB) 50
- Watchdog flag 50
- WATCHDOG TIMER (Cont’d) 51
- Time base control 53
- Oscillator interrupt enable 53
- Oscillator interrupt flag 53
- clock speed) with the choice 54
- 16-BIT TIMER (Cont’d) 55
- Beginning of the sequence 56
- Sequence completed 56
- /CC[1:0]) 58
- 16-BIT FREE RUNNING 59
- OLVL2OLVL1 64
- Pulse Width Modulation cycle 65
- Input Capture Flag 1 69
- Output Compare Flag 1 69
- Timer Overflow Flag 69
- Input Capture Flag 2 69
- Output Compare Flag 2 69
- CAPTURE STROBE 77
- VR02131B 77
- Write Collision status 83
- Mode Fault flag 83
- TDRE TC RDRF IDLE OR NF FE 93
- R8 T8 - M WAKE - 94
- TIE TCIE RIE ILIE TE RE RWU 94
- First SCI Prescaler 95
- SCI Transmitter rate divisor 95
- SCI Receiver rate divisor 95
- 8-bit Extended Receive Pres 96
- 8-bit Extended Transmit Pres 96
- CH2 CH1CH3COCO 0 ADON 0 CH0 97
- ■ A/D conversion [duration: t 98
- D7 D6 D5 D4 D3 D2 D1 D0 99
- COCO 0 ADON 0 CH3 CH2 CH1 CH0 99
- 15 INSTRUCTION SET 101
- Relative (Indirect) 103
- INSTRUCTION GROUPS (Cont’d) 105
- 16 ELECTRICAL CHARACTERISTICS 107
- 16.6 MEMORY CHARACTERISTICS 122
- 16.6.2 EEPROM Data Memory 122
- 16.6.3 FLASH Program Memory 122
- R=10k~10MΩ 124
- UNUSED I/O PORT 128
- ADC Accuracy 139
- 17 PACKAGE CHARACTERISTICS 140
- ■ Heraeus: PD945, PD955 143
- ■ Loctite: 3615, 3298 143
- MICROCONTROLLER OPTION LIST 146
- DEVELOPMENT TOOLS (Cont’d) 148
- 18.4 ST7 APPLICATION NOTES 149
- 19 IMPORTANT NOTES 151
- 20 SUMMARY OF CHANGES 152
Verwandte Produkte und Handbücher für Videokonverter Benchmark ADC16
(9 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.237 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern