Benchmark ADC16 Datenblatt Seite 47
- Seite / 153
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
ST72334J/N, ST72314J/N, ST72124J
47/153
MISCELLANEOUS REGISTERS (Cont’d)
13.3 REGISTERS DESCRIPTION
MISCELLANEOUS REGISTER 1 (MISCR1)
Read/Write
Reset Value: 0000 0000 (00h)
Bit 7:6 = IS1[1:0]
ei2 and ei3 sensitivity
The interrupt sensitivity, defined using the IS1[1:0]
bits, is applied to the following external interrupts:
ei2 (port B3..0) and ei3 (port B7..4). These 2 bits
can be written only when the I bit of the CC register
is set to 1 (interrupt disabled).
Bit 5 = MCO
Main clock out selection
This bit enables the MCO alternate function on the
I/O port. It is set and cleared by software.
0: MCO alternate function disabled
(I/O pin free for general-purpose I/O)
1: MCO alternate function enabled
(f
OSC
/2 on I/O port)
Note: To reduce power consumption, the MCO
function is not active in ACTIVE-HALT mode.
Bit 4:3 = IS2[1:0]
ei0 and ei1 sensitivity
The interrupt sensitivity, defined using the IS2[1:0]
bits, is applied to the following external interrupts:-
ei0 (port A3..0) and ei1 (port F2..0). These 2 bits
can be written only when the I bit of the CC register
is set to 1 (interrupt disabled).
Bit 2:1 = CP[1:0]
CPU clock prescaler
These bits select the CPU clock prescaler which is
applied in the different slow modes. Their action is
conditioned by the setting of the SMS bit. These
two bits are set and cleared by software
Bit 0 = SMS
Slow mode select
This bit is set and cleared by software.
0: Normal mode. f
CPU
= f
OSC
/ 2
1: Slow mode. f
CPU
is given by CP1, CP0
See low power consumption mode and MCC
chapters for more details.
70
IS11 IS10 MCO IS21 IS20 CP1 CP0 SMS
External Interrupt Sensitivity IS11 IS10
Falling edge & low level 0 0
Rising edge only 0 1
Falling edge only 1 0
Rising and falling edge 1 1
f
CPU
in SLOW mode CP1 CP0
f
OSC
/ 4 0 0
f
OSC
/ 8 1 0
f
OSC
/ 16 0 1
f
OSC
/ 32 1 1
- ST72334J/N 1
- ST72314J/N, ST72124J 1
- Table of Contents 2
- 2 INTRODUCTION 6
- 3 PIN DESCRIPTION 7
- (N versions) 8
- (J versions) 9
- 4 REGISTER & MEMORY MAP 13
- 5 FLASH PROGRAM MEMORY 17
- 6 DATA EEPROM 18
- Interrupt enable 21
- Latch Access Transfer 21
- 8 CENTRAL PROCESSING UNIT 23
- Half carry 24
- Interrupt mask 24
- Negative 24
- Carry/borrow 24
- 00000001 25
- MAIN CLOCK 26
- CONTROLLER 26
- ■ an external source 30
- ■ an external RC oscillator 30
- LVD reset flag 32
- Clock security syst 32
- interrupt enable 32
- Watchdog reset flag 32
- 10 INTERRUPTS 33
- INTERRUPTS (Cont’d) 34
- Table 5. Interrupt mapping 34
- 11 POWER SAVING MODES 35
- 12 I/O PORTS 39
- Hardware Configuration 41
- OPEN-DRAIN OUTPUT 41
- PUSH-PULL OUTPUT 41
- Data register 8 bits 44
- Option register 8 bits 44
- I/O PORTS (Cont’d) 45
- 13 MISCELLANEOUS REGISTERS 46
- Main clock out selection 47
- CPU clock prescaler 47
- Slow mode select 47
- Must always be cleared 48
- Beep control 48
- SS mode selection 48
- SS internal mode 48
- 14 ON-CHIP PERIPHERALS 49
- Activation bit 50
- 7-bit timer (MSB to LSB) 50
- Watchdog flag 50
- WATCHDOG TIMER (Cont’d) 51
- Time base control 53
- Oscillator interrupt enable 53
- Oscillator interrupt flag 53
- clock speed) with the choice 54
- 16-BIT TIMER (Cont’d) 55
- Beginning of the sequence 56
- Sequence completed 56
- /CC[1:0]) 58
- 16-BIT FREE RUNNING 59
- OLVL2OLVL1 64
- Pulse Width Modulation cycle 65
- Input Capture Flag 1 69
- Output Compare Flag 1 69
- Timer Overflow Flag 69
- Input Capture Flag 2 69
- Output Compare Flag 2 69
- CAPTURE STROBE 77
- VR02131B 77
- Write Collision status 83
- Mode Fault flag 83
- TDRE TC RDRF IDLE OR NF FE 93
- R8 T8 - M WAKE - 94
- TIE TCIE RIE ILIE TE RE RWU 94
- First SCI Prescaler 95
- SCI Transmitter rate divisor 95
- SCI Receiver rate divisor 95
- 8-bit Extended Receive Pres 96
- 8-bit Extended Transmit Pres 96
- CH2 CH1CH3COCO 0 ADON 0 CH0 97
- ■ A/D conversion [duration: t 98
- D7 D6 D5 D4 D3 D2 D1 D0 99
- COCO 0 ADON 0 CH3 CH2 CH1 CH0 99
- 15 INSTRUCTION SET 101
- Relative (Indirect) 103
- INSTRUCTION GROUPS (Cont’d) 105
- 16 ELECTRICAL CHARACTERISTICS 107
- 16.6 MEMORY CHARACTERISTICS 122
- 16.6.2 EEPROM Data Memory 122
- 16.6.3 FLASH Program Memory 122
- R=10k~10MΩ 124
- UNUSED I/O PORT 128
- ADC Accuracy 139
- 17 PACKAGE CHARACTERISTICS 140
- ■ Heraeus: PD945, PD955 143
- ■ Loctite: 3615, 3298 143
- MICROCONTROLLER OPTION LIST 146
- DEVELOPMENT TOOLS (Cont’d) 148
- 18.4 ST7 APPLICATION NOTES 149
- 19 IMPORTANT NOTES 151
- 20 SUMMARY OF CHANGES 152
Verwandte Produkte und Handbücher für Videokonverter Benchmark ADC16
(9 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern